How to Open Blink Camera

Do you want to know how to open blink camera? It’s really easy, and in this blog post, I will show you how. There are many reasons why it’s important to open your blink camera. For starters, opening your camera allows you to control your device fully. It also makes it easier to update the firmware and make other changes to your camera. Additionally, opening your camera can help you troubleshoot any problems you may be having with it. So, if you want to learn how to open your blink camera, keep reading!

How to Open Blink Camera

Step 1: Remove the Camera Module

Before you can open your blink camera, you need to remove the camera module from the board. The first thing you have to do is disconnect any cables or wires attached to it. Next, use your screwdriver and unscrew any screws holding it in place until it’s loose enough for you to take it out of the frame easily. Once you remove the camera, set it aside and continue with how to open blink camera guide.

Step 2: Unscrew the Modules

There are two screws that you need to unscrew; one is located under each door. Use your screwdriver of choice; I use an eyeglass repair kit because it uses the same small flathead screwdrivers, and they’re everywhere. You can probably find something like this at any grocery or hardware store for cheap.

Step 3: Remove the Top

The screw you just removed is how the top module attaches to the base. The top cover should come away pretty quickly, exposing a space for your batteries and a circuit board with some LEDs. This circuit board doesn’t do anything other than power your Blink camera’s LEDs; it’s how you tell the camera how to behave. We will talk a bit more about this circuit board later on.

Step 4: Remove the Bottom

The bottom of your Blink is where all of the real action happens. It has all your motion sensors, a battery compartment, and a reset button. You’ll need to pull this apart to access the batteries, which are how the camera remembers how much charge it has when you unplug it.

Step 5: Open the Batteries’ Door

Put two new AA batteries into the battery compartment. If you are not sure which are the positive and negative ends, look closely at the side of the battery with your camera’s zoom lens on it. The end with a + sign contains more zinc or lithium than its neighbor, which is how the manufacturing company can differentiate between them.

Open the Batteries Case

Step 6: Put It All Back Together

Blink should reassemble fairly easily. make sure to close the battery door tightly, and remember to screw in the modules (the part with the LEDs) before you close up your Blink frame.

Step 7: Finish Up

Your Blink has been successfully reassembled! Launch your Blink mobile app and check how much energy it has. You can also snap a photo or two with the built-in camera if you want. When plugged into power, you’ll notice that your Blink will always give itself a full charge before going into sleep mode. So as long as you plug your Blink in every night, it’ll always be running at 100% battery.

If you are looking at how to open the xt and xt2 blink camera, you are in luck! This handy how-to guide can show you how to open blink. If your Blink is not turning on or has other problems, this how-to guide will get you up and running!

1. Make The Camera’s Rear Face You

To open your Blink camera, you will need to make the camera’s rear face you. This is because the rear panel is where the battery is located, and you will need to remove it to access the camera’s interior. To do this, locate the seam on the back of the camera and use your fingernail or a flat object to pry it open.

2. Slide and Hold the Grey Switch

You will need to slide and hold the grey switch to remove the battery. This is located on the bottom of the camera. Once the switch has been depressed, the battery will release and can be removed.

3. Place the Battery in an Energizer Charger

If your blink camera is not turning on, no power may run through the battery. This how-to guide can help you learn how to open Blink XT or XT2 to check that there isn’t something wrong with the battery. If the battery is dead, place the battery in an energizer charger for about an hour, and then try turning on your Blink camera again.

4. Warning – Requires Some Force

Please be aware that you will need to apply some force to open the XT or XT2 Blink. So make sure you are careful when prying open the camera’s rear panel. Also, keep in mind that the battery is located in the rear panel and needs to be removed to access the camera’s interior.

apply some force to open the XT or XT2 Blink

5. Lift the Cover Off

Once the battery has been removed, you can lift the cover off of the camera. Be careful not to damage the cover, as it is fragile. This is how you will be able to access the interior of your Blink Camera.

If you are trying how to open the indoor blink camera, this how-to guide will show how it is done. To access the interior of your Blink camera, please follow these steps:

1. Remove the Battery Cover

To get your Blink Indoor Camera up and running again, you need to remove the battery cover. To remove your Blink Battery Cover, gently pry it from the front until all the catches have been released.

2. Remove and Replace battery

To how open a Blink indoor camera, you will need to make sure that there is a functioning battery inside. Please take out your Blink’s battery and make sure that it is charged by placing it in an energizer charger for about an hour. Then re-insert the battery back into your Blink Camera and try it.

Please Note: Before you how open a Blink indoor camera, please make sure that your Blink is turned off. Also, if you know how to open a blink indoor camera, please do not use tools.

Turn Off the Blink

To open the Blink Camera, you will need a key with each camera. The key helps prevent tampering with the SD card and battery compartment. To remove the back of your Blink Camera, just put the key into the slot on top of your camera twist it counter-clockwise until you hear a click. Then slide the top of the camera down to remove it.

You should see a small silver screw that holds your SD card in place. Remove the screw by turning it counter-clockwise with a Phillips head screwdriver. Then take out your Blink Camera’s battery, along with the card.

Here are a few tips on how to open the indoor and outdoor blink camera:

Removable Silicone Cover

The removable silicone cover also helps protect your camera from the elements and keeps it looking new. To remove the cover, pinch the sides and pull it off.

Keep for Future Use

If you ever want to put the cover back on, slide it over the camera and push down on all four corners until it clicks. Please keep this for future use if you need to reference how to open your Blink Camera.

Transparent Sticker

If you want to remove the transparent sticker on the lens of your Blink Camera, peel it off. Be careful not to scratch the lens.

Loosen the Screw

You can also loosen the screw that holds your SD card in place by turning it counter-clockwise with a Phillips head screwdriver.

Loose the Screw

Press It Into Place

Once you have removed the battery, SD card, and screw, you can press the Blink Camera into place. First, line up the four gold contacts on the bottom of the camera with the four corresponding contacts on the base. Then use your thumb and index finger to push down on each side of the camera until it snaps into place.

Apply Side Pressure

Apply side pressure to the camera until it snaps into place. You can press along the sides of the camera, not just over the place where it attaches.

Line them Up

Line the four gold contacts on the bottom of the camera up with the four corresponding contacts on the base.

Clockwise Turn

To reattach the back, twist it clockwise until you hear a click. Then slide the camera’s top back on until it snaps into place.

To disassemble a Blink Camera, you will need a key for each camera. The key helps prevent tampering with the SD card and battery compartment. For example, to remove the back of your Blink Camera, just put the key into the slot on top of your camera twist it counter-clockwise until you hear a click. Then slide the top of the camera down to remove it.

You should see a small silver screw that holds your SD card in place. Remove the screw by turning it counter-clockwise with a Phillips head screwdriver. Then take out your Blink Camera’s battery, along with the card. Thanks for reading our post about how to open blink camera.

Other Things You Should Notice

The Blink camera is aimed at people looking for an alternative to the security system. The device has a motion sensor, but it cannot record videos like many competitors. If you want more than one Blink Camera, multiple cameras can be linked to work through the same account; they will share their images and inform each other of any movements detected.

Other Things You Should Know About

Other Things You Should Notice:

  • The Blink Camera will not record or capture footage during an outage.
  • It is recommended to have a UPS for the Blink Camera.
  • The 1-year warranty covers power outages.

Can Power Outages Affect The Blink Camera? 

As blackouts and other power outages become increasingly common, it is essential to understand the potential effects on devices such as the Blink Camera. Power outages can lead to disconnection, a precursor to electrical disruption.

This risks casualties in certain electronic products, including the Blink Camera. However, this problem can be prevented by taking appropriate preventive measures, such as connecting your Blink Camera to an uninterruptible power supply. This type of power supply provides the Blink Camera with an uninterrupted voltage, ensuring that it is safe from electrical disruption in the event of a power outage.

Additionally, you can also back up important data or footage stored on your device to ensure its safety during a blackout. Following these simple steps will help protect your Blink Camera from any damage caused by power outages.

In conclusion, power outages can affect the Blink Camera if proper steps are not taken to protect it. However, with appropriate preventive measures, such as connecting your device to an uninterruptible power supply and backing up important data and footage, you can ensure that your Blink Camera remains safe in the event of a blackout or power outage.

Frequently Asked Question

The Blink Camera can operate during outages. If the power goes out, the camera will store the last image captured until power is restored. It will not provide the last few seconds of video prior to a power outage, but it will hold on to any images or video from during the outage.

If your Blink camera is not working, the first thing you should check is to make sure it is properly plugged in. The camera must be plugged into an outlet and a USB port on your computer to function.

If your camera is still not working, you may want to try resetting it. First, unplug the camera from both the outlet and your computer, then wait 30 seconds. After that, plug the camera back in and try again.

If your Blink Camera is offline, it may be due to one of several reasons:

  • The camera is not plugged in correctly. Ensure the camera is plugged into an outlet and a USB port on your computer.
  • The camera has lost power. If the camera is not plugged into an outlet, it will lose power after a few minutes.
  • There is an issue with your network. If you have trouble connecting to your Blink Camera, try restarting your router.

You Can Check It Out to: Install Blink Camera on Brick Wall

Conclusion

So there you have it – a simple guide on how to open blink camera. If you’re still experiencing issues, or have any other questions about using your camera, check out our support page or contact us for help. And don’t forget to keep an eye on our blog and social media pages for Blink’s latest news and updates!

You may also read: How to Install Security Camera Without Drilling

2 thoughts on “How to Open Blink Camera”

Leave a Comment